[wplug] fsck running in background?
John Harrold
jmh17 at pitt.edu
Wed Sep 22 14:12:54 EDT 2004
Sometime in September Poyner, Brandon assaulted the keyboard and produced:
| If the drive is SMART enabled you can also use smartctl to get the SMART
| information or run a long or short SMART test. That will at least tell
| you if the drive itself thinks there is an error.
|
| http://smartmontools.sourceforge.net/
So running 'smartctl -a /dev/hdc' I got the following output:
I'm still going to check the cable when I have physical access to the
machine. I'm still running badblocks --- it takes a while.
<output>
smartctl version 5.32 Copyright (C) 2002-4 Bruce Allen
Home page is http://smartmontools.sourceforge.net/
=== START OF INFORMATION SECTION ===
Device Model: WDC WD2500JB-32FUA0
Serial Number: WD-WMAEP1124347
Firmware Version: 15.05R15
Device is: In smartctl database [for details use: -P show]
ATA Version is: 6
ATA Standard is: Exact ATA specification draft version not indicated
Local Time is: Wed Sep 22 13:44:30 2004 EDT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: FAILED!
Drive failure expected in less than 24 hours. SAVE ALL DATA.
See vendor-specific Attribute list for failed Attributes.
General SMART Values:
Offline data collection status: (0x84) Offline data collection activity
was suspended by an interrupting command from host.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (7617) seconds.
Offline data collection
capabilities: (0x79) SMART execute Offline immediate.
No Auto Offline data collection support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
No General Purpose Logging support.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 95) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000b 001 001 051 Pre-fail Always FAILING_NOW 3476
3 Spin_Up_Time 0x0007 100 253 021 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 100 100 040 Old_age Always - 3
5 Reallocated_Sector_Ct 0x0033 199 199 140 Pre-fail Always - 4
7 Seek_Error_Rate 0x000b 200 200 051 Pre-fail Always - 0
9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 387
10 Spin_Retry_Count 0x0013 100 253 051 Pre-fail Always - 0
11 Calibration_Retry_Count 0x0013 100 253 051 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 3
194 Temperature_Celsius 0x0022 112 253 000 Old_age Always - 38
196 Reallocated_Event_Count 0x0032 196 196 000 Old_age Always - 4
197 Current_Pending_Sector 0x0012 173 173 000 Old_age Always - 1103
198 Offline_Uncorrectable 0x0012 196 196 000 Old_age Always - 197
199 UDMA_CRC_Error_Count 0x000a 200 253 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x0009 001 155 051 Pre-fail Offline FAILING_NOW 65535
SMART Error Log Version: 1
ATA Error Count: 120 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 120 occurred at disk power-on lifetime: 381 hours (15 days + 21 hours)
When the command that caused the error occurred, the device was doing SMART Offline or Self-test.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 08 54 00 0c e0 Error:
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
00 00 25 00 00 08 00 00 16d+09:11:34.700 NOP [Abort queued commands]
1c 00 0c 00 00 3f 00 00 16d+09:11:34.700 RECALIBRATE [RET-4]
00 00 25 00 00 08 00 00 16d+09:11:34.700 NOP [Abort queued commands]
00 00 25 00 00 08 00 00 16d+09:11:34.700 NOP [Abort queued commands]
11 00 7c 00 00 37 11 00 16d+09:11:34.700 RECALIBRATE [RET-4]
Error 119 occurred at disk power-on lifetime: 381 hours (15 days + 21 hours)
When the command that caused the error occurred, the device was doing SMART Offline or Self-test.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 10 49 00 0c e0 Error:
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
00 00 25 00 00 10 00 00 16d+09:11:28.350 NOP [Abort queued commands]
1c 00 08 00 00 47 00 00 16d+09:11:28.350 RECALIBRATE [RET-4]
00 00 35 00 00 80 00 00 16d+09:11:28.350 NOP [Abort queued commands]
00 00 25 00 00 08 00 00 16d+09:11:28.350 NOP [Abort queued commands]
11 00 7c 00 00 37 11 00 16d+09:11:28.350 RECALIBRATE [RET-4]
Error 118 occurred at disk power-on lifetime: 381 hours (15 days + 21 hours)
When the command that caused the error occurred, the device was doing SMART Offline or Self-test.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 18 49 00 0c e0 Error:
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
00 00 25 00 00 18 00 00 16d+09:11:25.000 NOP [Abort queued commands]
00 00 00 00 00 3f 00 00 16d+09:11:25.000 NOP [Abort queued commands]
00 00 25 00 00 08 00 00 16d+09:11:25.000 NOP [Abort queued commands]
11 00 7c 00 00 37 11 00 16d+09:11:25.000 RECALIBRATE [RET-4]
00 00 25 00 00 08 00 00 16d+09:11:25.000 NOP [Abort queued commands]
Error 117 occurred at disk power-on lifetime: 378 hours (15 days + 18 hours)
When the command that caused the error occurred, the device was doing SMART Offline or Self-test.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 80 69 10 7c e0 Error:
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
00 00 25 00 00 80 00 00 16d+05:27:42.700 NOP [Abort queued commands]
11 00 7c 00 00 37 0f 00 16d+05:27:42.700 RECALIBRATE [RET-4]
00 00 25 00 00 80 00 00 16d+05:27:42.700 NOP [Abort queued commands]
00 00 25 00 00 80 00 00 16d+05:27:42.700 NOP [Abort queued commands]
11 00 7c 00 00 37 0d 00 16d+05:27:42.700 RECALIBRATE [RET-4]
Error 116 occurred at disk power-on lifetime: 378 hours (15 days + 18 hours)
When the command that caused the error occurred, the device was doing SMART Offline or Self-test.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 78 e3 10 98 e0 Error:
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
00 00 25 00 00 78 00 00 16d+05:21:56.000 NOP [Abort queued commands]
0f 00 98 00 00 17 10 00 16d+05:21:56.000 [RESERVED]
00 00 25 00 00 80 00 00 16d+05:21:56.000 NOP [Abort queued commands]
00 00 25 00 00 80 00 00 16d+05:21:56.000 NOP [Abort queued commands]
0f 00 98 00 00 17 0e 00 16d+05:21:56.000 [RESERVED]
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
</output>
--
----------------------------------------------------------
| /"\
john harrold | \ / ASCII ribbon campaign
jmh at member.fsf.org | X against HTML mail
the most useful idiot | / \
----------------------------------------------------------
What difference does it make to the dead, the orphans,
and the homeless, whether the mad destruction is brought
under the name of totalitarianism or the holy name of
liberty and democracy?
--Gandhi
----------------------------------------------------------
gpg --keyserver keys.indymedia.org --recv-key F65A739E
----------------------------------------------------------
More information about the wplug
mailing list